Insulation in Brea, CA
Spray foam insulation in Brea is the single most effective fix for homes here because the city sits in California Energy Commission Climate Zone 10, the same hot-inland classification as Riverside, not the milder coastal rating that applies to Anaheim or Fullerton just a few miles west. Most Brea houses were built between the 1960s and 1980s with R-11 to R-19 attic batts, far short of the R-38 to R-49 that current Title 24 requires for Zone 10. That gap shows up as summer attics that push past 140°F and air conditioning bills that never seem to drop, no matter how low you set the thermostat. Call Walt’s Insulation at (657) 214-8224 and we’ll tell you straight whether your house needs foam, blown-in, or something else entirely.
Why Brea Homes Are Different
Brea’s inland position at the base of the Puente Hills regularly drives summer highs 8-12°F above coastal Orange County, which means the dominant insulation priority here is cooling-load reduction, not winter warmth. The city’s core neighborhoods, Country Hills among them, were built as stucco-over-wood-frame ranch and two-story colonial tract homes, many still carrying original fiberglass batts and wall cavities that were never sealed. The newer Blackstone community on the northern hillside was built to modern Title 24 standards, so those homes rarely need what the older tracts need.
The terrain creates something most flat OC cities never see. Carbon Canyon funnels Santa Ana wind events directly into the hillside neighborhoods near Olinda and Carbon Canyon, so homes there face a dual failure mode: south-facing roof planes that superheat attics in summer and northeast winds that pressurize wall cavities in winter. An insulation tech working in Brea has to address both radiant-heat gain and wind-driven air sealing on the same job, not just one or the other.
Our Main Brea Services
Two services get the most calls from Brea homeowners, and they line up directly with the housing stock and climate here.
Attic Insulation in Brea
Most Brea attics in the 1960s-1980s tracts are running R-11 to R-19, which was code at the time but is now less than half of what Zone 10 demands. We remove or top up what’s there and bring the attic to R-38 or better, which immediately flattens the afternoon heat gain that makes upstairs rooms unusable in August. The work is straightforward in Brea’s standard ranch and colonial attics, but hillside homes near Carbon Canyon often need air sealing done at the same time or the new insulation won’t perform. See Attic Insulation in Brea for the full breakdown.
Crawl Space Encapsulation & Vapor Barrier in Brea
Brea’s older tract homes sit on crawl spaces that were vented to outside air, which in this climate means hot, humid summer air drawn into the space under the house and cold, dry Santa Ana wind pushing through it in winter. That cycle rots floor framing and pushes musty air up into living spaces. Encapsulating the crawl space with a vapor barrier and sealing the vents stops both problems at once, and it cuts the stack effect that pulls attic heat down through the house. Read Crawl Space Encapsulation & Vapor Barrier in Brea for specifics.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Spray Foam Insulation in Brea
Spray foam insulation in Brea closes the gap between what 1960s-1980s tract homes were built with and what Zone 10 actually demands. Closed-cell foam in particular does two jobs at once here: it insulates to R-6.5 per inch and it air-seals, which matters when Santa Ana winds channeled through Carbon Canyon pressurize wall cavities and force conditioned air out. For Brea homeowners with attics hitting 140°F in summer, foam on the roof deck can turn an unconditioned attic into a semi-conditioned space and drop upstairs temperatures noticeably. This is the job we do most often in Country Hills and the other established neighborhoods, and it’s what we’d recommend first for any Brea home built before 1990. See our Spray Foam Insulation service page for full details on materials and methods.
Open-Cell Spray Foam
Signs you need it
Upstairs rooms run 10-15°F hotter than downstairs in summer, or your AC short-cycles because the attic keeps re-heating the house.
What it costs in Brea
Open-cell foam on a Brea attic floor or roofline typically runs $2.00-$3.50 per board foot, with most whole-attic jobs landing between $4,000 and $8,000 depending on square footage and depth.
How we do it
We prep the attic by sealing bypasses, then spray the foam to the specified depth, letting it expand, cure, and form a continuous air and thermal barrier before we re-check the hatch and any recessed lights.
Closed-Cell Spray Foam
Signs you need it
You need high R-value per inch and moisture resistance, often because the attic is shallow or the roof deck is exposed to wind-driven rain off the Puente Hills.
What it costs in Brea
Closed-cell foam in Brea runs $3.50-$5.50 per board foot, and a typical attic roof deck job falls between $6,000 and $14,000 given the R-38+ depths required in Zone 10.
How we do it
We spray the foam directly onto the roof deck or rim joist surfaces in controlled passes, building to the specified thickness, then trim and inspect for full adhesion and coverage.
What Spray Foam Insulation Costs in Brea
| Item | Typical range in Brea |
|---|---|
| Open-cell foam (per board foot) | $2.00-$3.50 |
| Closed-cell foam (per board foot) | $3.50-$5.50 |
| Whole-attic foam (open-cell, typical ranch) | $4,000-$8,000 |
Is closed-cell foam worth the extra cost in Brea?
For most Brea homes, yes, especially if the attic is shallow or the roof deck gets direct afternoon sun. Closed-cell adds moisture resistance and structural rigidity, and the higher R-per-inch means you can hit Zone 10 targets in less depth. Call (657) 214-8224 for a breakdown on your specific attic.
Can you spray foam my attic the same week in Brea?
Most Brea spray foam jobs are scheduled within 5-7 business days once we’ve done the site check and you’ve approved the quote. We answer the phone live around the clock, so call (657) 214-8224 and we’ll set a date on the spot if we have an opening.
Blown-In Insulation in Brea
Blown-in insulation in Brea is usually the most cost-effective way to bring an older attic up to Zone 10 code, because most 1960s-1980s tract homes here are running R-11 to R-19 when the current requirement is R-38 to R-49. Cellulose and fiberglass both work, but we lean toward cellulose in Brea because it settles into the odd cavities and bypasses that plague ranch and colonial framing from that era. The payoff is immediate: attic temperatures stop radiating into the house by late afternoon, and the AC finally cycles off. Our Blown-In Insulation page covers material differences and depth charts.
Blown-In Cellulose
Signs you need it
Your attic insulation is compressed, settled, or measures below R-30 when you check it, and your upstairs rooms heat up by mid-afternoon.
What it costs in Brea
Blown-in cellulose in Brea runs $1.50-$3.00 per square foot installed, so a typical 1,200-square-foot attic lands between $1,800 and $3,600 to reach R-38.
How we do it
We seal the major bypasses, mark the target depth, then blow cellulose through a calibrated hose in even passes until the entire attic floor reads at or above the R-value you’re paying for.
Blown-In Fiberglass
Signs you need it
You want an insulation that won’t settle over time and prefer a material that’s less dusty during installation than cellulose.
What it costs in Brea
Blown-in fiberglass in Brea runs $1.75-$3.50 per square foot installed, with most whole-attic jobs falling between $2,100 and $4,200 for R-38 coverage.
How we do it
We run the fiberglass through a blower at the specified density, building depth in layers so the final R-value is consistent across the entire attic floor, including edges and corners.
What Blown-In Insulation Costs in Brea
| Item | Typical range in Brea |
|---|---|
| Blown-in cellulose (per sq ft) | $1.50-$3.00 |
| Blown-in fiberglass (per sq ft) | $1.75-$3.50 |
| Whole-attic top-up to R-38 (typical ranch) | $1,800-$4,200 |
Does blown-in insulation work as well as spray foam in Brea’s heat?
For attic floors, blown-in cellulose or fiberglass at R-38 to R-49 works well and costs significantly less than foam. Foam wins when you need air sealing in the same pass or want to condition the attic space itself. Call (657) 214-8224 and we’ll tell you which makes sense for your house.
Can you blow insulation over what’s already in my Brea attic?
In most cases yes, once we confirm the existing material is dry, not rodent-contaminated, and not vermiculite. We top up to the Zone 10 target of R-38 or better with one pass. Call (657) 214-8224 for a same-week attic check.
Radiant Barrier Installation in Brea
Radiant barrier installation in Brea cuts heat gain at the source, which matters when your attic pushes past 140°F because the south-facing roof plane has been baking all afternoon. A radiant barrier stapled under the rafters reflects the sun’s heat before it ever reaches your insulation and living space, which in Zone 10 can reduce attic temperatures by 20-30°F. For Brea homes near the Olinda and Carbon Canyon hillsides, where the rooflines catch full southern exposure, this is often the single fastest improvement we can make. Pairing it with proper ventilation and either blown-in or foam insulation delivers the biggest total drop. See Radiant Barrier Installation for the full explanation of how the reflective surface works.
Attic Radiant Barrier
Signs you need it
Your attic is uncomfortable to stand in after noon, your AC runs constantly in July and August, and your roof has large south-facing planes with direct sun exposure.
What it costs in Brea
A radiant barrier in a typical Brea attic runs $1.50-$2.50 per square foot installed, so most 1,200-1,500-square-foot attics land between $1,800 and $3,750.
How we do it
We staple the reflective foil to the underside of the rafters across the full roofline, leaving the ridge and soffit vents clear so air still moves, then inspect for any tears or gaps.
Radiant Barrier & Ventilation
Signs you need it
Your attic has a radiant barrier or extra insulation but still overheats because the existing vents are undersized or blocked by old insulation.
What it costs in Brea
Adding or upgrading ventilation alongside a radiant barrier typically adds $300-$700 to the job in Brea, depending on whether we’re adding soffit, gable, or ridge vents.
How we do it
We measure the attic’s intake and exhaust ventilation, add the vents needed to bring it to the 1:300 ratio, then install the barrier so the reflective surface stays clean and effective.
What Radiant Barrier Installation Costs in Brea
| Item | Typical range in Brea |
|---|---|
| Radiant barrier (per sq ft) | $1.50-$2.50 |
| Full attic, 1,200-1,500 sq ft | $1,800-$3,750 |
| Added ventilation work | $300-$700 |
Does a radiant barrier work in winter in Brea?
Yes, though the main benefit here is summer. The same reflective surface that blocks afternoon solar gain also reduces heat loss on cold winter nights, and it doesn’t interfere with the Santa Ana wind-driven air sealing we’d do separately. Call (657) 214-8224 if you want a summer-focused plan.
Can you install a radiant barrier in a Brea attic with low headroom?
Yes, we work in attics with shallow pitch and low clearance regularly in Brea’s ranch homes. The foil staples to rafters and doesn’t add bulk, so headroom isn’t a limiting factor. Call (657) 214-8224 and we’ll tell you what your specific roofline can take.
Insulation Removal & Replacement in Brea
Insulation removal and replacement in Brea comes up most often when old fiberglass batts from the 1960s-1980s have been soaked by roof leaks, shredded by rodents, or contaminated by droppings and dust from decades of open-vented attics. In a city where Santa Ana winds push through Carbon Canyon and pressure the attic, degraded insulation loses even more of its already low R-value, and the house starts behaving like it has no insulation at all. We remove the old material down to the deck, treat and sanitize where needed, then install new insulation built for Zone 10’s R-38 to R-49 requirement. See Insulation Removal & Replacement for the step-by-step process.
Contaminated Insulation Removal
Signs you need it
You smell must or rodent odor coming from the attic, or you’ve found droppings, nesting material, or water stains on the existing insulation.
What it costs in Brea
Contaminated insulation removal in Brea typically runs $2.00-$3.50 per square foot, so a 1,200-square-foot attic lands between $2,400 and $4,200 before replacement material.
How we do it
We bag and remove the contaminated material through a HEPA-filtered vacuum, sanitize the attic surfaces, seal the rodent entry points, then install fresh insulation to the Zone 10 target.
Insulation Replacement
Signs you need it
Your existing batts are compressed, water-damaged, or measure below R-19, and you want a clean start rather than a top-up over compromised material.
What it costs in Brea
Full removal and replacement in a Brea attic usually runs $2.50-$4.00 per square foot all-in, with most 1,200-square-foot jobs landing between $3,000 and $4,800 depending on the new material.
How we do it
We remove everything down to the deck, inspect and seal the attic floor, then blow or batt the new material to R-38 or better and verify the depth with a gauge.
What Insulation Removal & Replacement Costs in Brea
| Item | Typical range in Brea |
|---|---|
| Contaminated removal (per sq ft) | $2.00-$3.50 |
| Full removal + replacement (per sq ft) | $2.50-$4.00 |
| Typical 1,200 sq ft attic, all-in | $3,000-$4,800 |
How do I know if my Brea attic insulation needs removal instead of a top-up?
If you see water stains, rodent droppings, or the material has compressed to less than R-19, removal is the right call. Topping up over contaminated insulation traps the problem. Call (657) 214-8224 and we’ll inspect it and give you a straight answer.
Will removing old insulation disturb asbestos in a Brea house?
Older Brea homes may have vermiculite insulation, which can contain asbestos. We don’t touch it until it’s been tested, and if it’s positive we work with a licensed abatement contractor before we return. Safety comes first, and we’ll tell you exactly what you’re dealing with.
Attic Air Sealing in Brea
Attic air sealing in Brea matters more than in most Orange County cities because Carbon Canyon funnels Santa Ana wind events directly into the hillside neighborhoods, pressurizing wall cavities and forcing conditioned air out through every unsealed penetration in the attic floor. A house can have R-38 insulation and still lose a huge share of its cooling if the top plates, can lights, and hatch aren’t sealed, because air moves straight through the insulation. In Brea’s older tracts, where the framing is full of bypasses from original construction, air sealing is the difference between an insulation job that works and one that just fills space. Our Attic Air Sealing page explains every leak point we cover.
Top Plate & Penetration Sealing
Signs you need it
You feel drafts near interior walls or can see daylight through gaps around plumbing vents and wiring penetrations in the attic.
What it costs in Brea
Top plate and penetration sealing in Brea typically runs $800-$1,500 for a standard ranch attic, depending on how many leaks and how much foam or caulk is needed.
How we do it
We work through the attic with foam and caulk, sealing every top plate joint, plumbing vent, wire chase, and chase wall that connects the attic to your conditioned space.
Attic Hatch Sealing
Signs you need it
Your pull-down stair or attic door is warm to the touch in summer, or you can feel air moving around the edges when you stand beneath it.
What it costs in Brea
Sealing and insulating a standard attic hatch in Brea runs $150-$300, including weatherstripping and a rigid foam cover if the hatch is accessible.
How we do it
We weatherstrip the hatch frame, add an insulated cover box or board over the opening, and seal the trim with foam so the hatch stops acting like an open window into the attic.
What Attic Air Sealing Costs in Brea
| Item | Typical range in Brea |
|---|---|
| Full attic air sealing (typical ranch) | $800-$1,500 |
| Can light & duct boot sealing | $300-$700 |
| Attic hatch sealing | $150-$300 |
Do I need air sealing if I’m already getting new insulation in Brea?
Yes, and in Brea’s wind-exposed hillside neighborhoods it’s not optional. Insulation slows heat transfer but doesn’t stop air movement, and Santa Ana winds will push right through unsealed penetrations. Call (657) 214-8224 and we’ll include sealing in the quote automatically.
How long does attic air sealing take in a Brea home?
Most Brea ranch and two-story homes take one workday, sometimes two if the attic is tight or the house has many can lights and duct boots to seal. We’ll give you a firm time window when we schedule. Call (657) 214-8224 to set a date.
Wall Insulation in Brea
Wall insulation in Brea is a common retrofit in the 1960s-1980s tract homes, many of which were built with empty or barely insulated wall cavities behind the stucco. When summer sun beats on those stucco walls and Santa Ana winds pressurize the cavities from the outside, the walls act like uninsulated ducts, moving heat and air through the house. Injecting foam or blowing dense-pack cellulose into the stud bays fills that void and immediately quiets the house while cutting the cooling load. The Blackstone homes on the northern hillside were built to modern code, so this work mostly applies to the older tracts. Our Wall Insulation page explains the difference between injection foam and drill-and-fill.
Injection Foam Wall Insulation
Signs you need it
Your exterior walls feel warm to the touch on summer afternoons, or rooms on the sun-facing side of the house are noticeably hotter than the rest.
What it costs in Brea
Injection foam wall insulation in Brea typically runs $2.50-$4.50 per square foot of wall area, so a 2,000-square-foot house with 1,600 square feet of exterior wall lands between $4,000 and $7,200.
How we do it
We drill small holes through the stucco or drywall at each stud bay, inject the foam to fill the cavity, then patch the holes so the exterior looks untouched.
Drill & Fill Wall Insulation
Signs you need it
You want the lower-cost option for filling empty stud bays, and you’re okay with cellulose or fiberglass instead of expanding foam.
What it costs in Brea
Drill-and-fill wall insulation in Brea runs $2.00-$3.50 per square foot of wall area, with most whole-house retrofits landing between $3,200 and $5,600.
How we do it
We drill access holes into each stud bay from the interior or exterior, blow the insulation to the target density, then patch and texture the holes to match.
What Wall Insulation Costs in Brea
| Item | Typical range in Brea |
|---|---|
| Injection foam (per sq ft of wall) | $2.50-$4.50 |
| Drill & fill (per sq ft of wall) | $2.00-$3.50 |
| Whole-house retrofit (typical 2,000 sq ft home) | $3,200-$7,200 |
Does wall insulation make a big difference in Brea’s heat?
If your walls are uninsulated or nearly empty, yes, it’s often the second biggest improvement after the attic. Wall cavities that act like hot air ducts can undermine the attic work entirely. Call (657) 214-8224 and we’ll assess your walls before you spend anything.
Will drilling into my stucco damage the exterior of my Brea home?
No, the holes are small and we patch them with color-matched stucco so the finish is clean. Most homeowners can’t find the drill points after we’re done. Call (657) 214-8224 and we’ll walk you through the process.
Attic Cleaning & Rodent Proofing in Brea
Attic cleaning and rodent proofing in Brea matters because the hillside neighborhoods near Olinda and Carbon Canyon back up to open chaparral, and rodents move into attics through the same wind-driven entry points that let Santa Ana air inside. Once they’re in, they shred fiberglass batts, soak insulation with urine, and leave droppings that make the attic a health hazard and the insulation useless. We clean out the contamination, sanitize the space, and seal the entry points so they can’t get back in. In Brea’s older tracts, this is often the necessary first step before any new insulation can go in. See Attic Cleaning & Rodent Proofing for the full scope.
Attic Cleanout
Signs you need it
You see droppings, nesting material, or shredded insulation in the attic, or you hear scratching in the walls and ceiling at night.
What it costs in Brea
A full attic cleanout in Brea typically runs $1,500-$3,000 for a standard 1,200-square-foot attic, including removal of contaminated insulation and debris.
How we do it
We remove all contaminated insulation and debris, vacuum the attic floor with HEPA filtration, then sanitize the surfaces before we move on to sealing.
Rodent Proofing & Exclusion
Signs you need it
You’ve had rodents return after removal, or you’ve found gaps, vents, or roof intersections where animals can squeeze through into the attic.
What it costs in Brea
Rodent proofing and exclusion in Brea runs $800-$2,500 depending on how many entry points we find and whether we’re screening vents, sealing gaps, or both.
How we do it
We inspect the roofline, vents, and eaves for every access point, seal them with exclusion-grade materials, then set the attic up for fresh insulation once it’s clean and dry.
What Attic Cleaning & Rodent Proofing Costs in Brea
| Item | Typical range in Brea |
|---|---|
| Attic cleanout (typical 1,200 sq ft) | $1,500-$3,000 |
| Rodent proofing & exclusion | $800-$2,500 |
| Attic sanitizing & decontamination | $500-$1,200 |
Do I need to clean my attic before new insulation in Brea?
If rodents or roof leaks have contaminated the existing insulation, yes, you should clean it out before adding anything new. New insulation over contaminated material doesn’t fix the odor or the health issue. Call (657) 214-8224 and we’ll tell you what we find up there.
Can you seal my Brea attic so rodents never come back?
Yes, exclusion work is exactly that, and we do it as standard on any Brea job where we find rodent activity. We seal every access point with materials they can’t chew through. Call (657) 214-8224 to schedule an inspection.
Home Energy Audit in Brea
A home energy audit in Brea pinpoints why your cooling bill stays high even when the AC runs all day, and in this climate the answer is almost always a combination of under-insulated attics, leaky ductwork, and wall cavities that were never sealed. Zone 10’s hot-inland conditions punish those failures harder than anywhere on the coast, and the 1960s-1980s housing stock here has all three problems built in. We run blower door and thermal imaging tests to find exactly where the house is losing conditioned air, then give you a prioritized list of fixes that actually pay back. It’s the fastest way to stop guessing and start fixing. Our Home Energy Audit page breaks down each test we run.
Blower Door Test
Signs you need it
Your energy bills are consistently high, rooms feel drafty, or you can’t figure out why the AC runs constantly in summer.
What it costs in Brea
A blower door test as part of a full audit in Brea runs $200-$400 when booked with other testing, or $300-$500 as a standalone visit.
How we do it
We mount the blower door in an exterior door frame, depressurize the house, and measure the total air leakage rate so we know exactly how leaky the envelope is.
Thermal Imaging Inspection
Signs you need it
Certain walls or ceilings feel cold in winter or hot in summer, and you want to see exactly where the insulation is missing or compressed.
What it costs in Brea
Thermal imaging as part of an audit in Brea adds $150-$300 to the blower door test, and we typically run both together on the same visit.
How we do it
We scan walls, ceilings, and floors with an infrared camera to map cold and hot spots, then correlate the images with the blower door data to pinpoint leaks and voids.
What Home Energy Audit Costs in Brea
| Item | Typical range in Brea |
|---|---|
| Full energy audit (blower door + thermal) | $350-$700 |
| Duct leakage test | $150-$300 |
| Insulation inspection | $100-$200 |
Is a home energy audit worth it before I insulate in Brea?
Yes, and we’d argue it’s the smartest first step. The audit tells you whether the problem is insulation, air leaks, ducts, or all three, so you spend money where it matters. Call (657) 214-8224 and we’ll book the audit before any work is quoted.
How long does a home energy audit take in Brea?
Most audits run 2-4 hours depending on house size and how many tests we’re running. You’ll get a written report with prioritized recommendations the same week. Call (657) 214-8224 to schedule a visit.
Brands We Service in Brea
We install and service insulation from Owens Corning, Johns Manville, Knauf, and GreenFiber in Brea homes, and we stock the most common materials locally so jobs don’t wait on shipments. See our brands page for the full list and what we recommend for Zone 10 attics.
Pricing for Insulation in Brea, CA
| Service | Typical range in Brea |
|---|---|
| Spray foam (open-cell, per board foot) | $2.00-$3.50 |
| Spray foam (closed-cell, per board foot) | $3.50-$5.50 |
| Blown-in insulation (per sq ft) | $1.50-$3.50 |
| Radiant barrier (per sq ft) | $1.50-$2.50 |
| Insulation removal (per sq ft) | $2.00-$3.50 |
| Attic air sealing (full attic) | $800-$1,500 |
| Wall insulation (per sq ft of wall) | $2.00-$4.50 |
| Attic cleanout | $1,500-$3,000 |
| Home energy audit | $350-$700 |
Prices in Brea push upward when we’re working in tight hillside attics with low clearance, or when rodent damage and wind-driven leaks force us to do removal, sealing, and replacement in the same visit. Every quote is upfront and itemized before we start, and the Done Right Promise stands behind every job we do.
Neighborhoods We Serve in Brea
We work throughout Brea, from the established tracts around the civic center to the hillside streets near the Puente Hills and the newer subdivisions on the north side. Response time across the city is typically same-day or next-day for emergencies, and we schedule regular work within the week.
- Country Hills
- Olinda
- Carbon Canyon
- Blackstone
- Central Brea
Service Area - Cities Near Brea
We serve Brea and the surrounding North Orange County cities, including La Habra, CA, Placentia, CA, Yorba Linda, CA, and Anaheim, CA. If you’re in one of these nearby cities, give us a call and we’ll get you on the schedule.
Serving Brea, CA - Our Local Coverage Area
We’re based in the Brea area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Insulation in Brea
We answer the phone live 24/7, and for emergency calls in Brea we can often have a technician at your door the same day. Regular estimates are usually scheduled within 2-3 business days. Call (657) 214-8224 and we’ll give you a straight time window for your specific neighborhood.
Do I need a permit for insulation work in Brea?
Most insulation retrofit work in Brea doesn’t require a permit at the city level, though some jobs that involve structural changes or
What happens when you call
- 1A real person answersNo phone trees - talk to a local insulation pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 30-60 min.
- 4You approve before work beginsNothing starts until you say go.
What Brea Customers Say
"We had the walls of our old house filled with foam through small holes from the outside. Patched and painted the same afternoon. The bedrooms hold heat now and the furnace runs a lot less."
- Linda Baumgartner"Good honest work on the attic. The price was a little higher than one online quote, but Walt is the one who actually showed up and the one whose name is on the truck, and that was worth it to us."
- Helen Tran"The house had rats in the attic insulation and a smell we could not place. Walt's crew pulled all of it, sealed the gaps where they were getting in, sanitized, and put in new blown-in. He sent photos of the sealed openings so I could see it done."
- Rosa Delgado